Kick Harness Killer Instinct

Kick Harness MK3 by HighScoreSaves Able to be used with Mortal Kombat 3, Ultimate Mortal Kombat 3 and Mortal Kombat 4These are approximately 4 foot long to give you the length needed Each wire has a .187 female quick disconnect on all player controls for attaching to the terminal on the microswitch (Not a cheap connector) This kick harness allows you to connect the low punch and low kick for both players. Standard JAMMA connectors only allow for 3 action buttons and MK2 uses 5 action buttons per player. MK2 pinout - At Connector P12 -7 = LP18 = LK19 = Run111 = LP212 = LK213 = Run2

Kick Harness MK2 by HighScoreSavesMortal Kombat II Player 1 and Player 2 Extra Buttons Auxiliary Kick JAMMA+ HarnessThese are approximately 4 foot long to give you the length needed Each wire has a .187 female quick disconnect on all player controls for attaching to the terminal on the microswitch (Not a cheap connector) This kick harness allows you to connect the low punch and low kick for both players. Standard JAMMA connectors only allow for 3 action buttons and MK2 uses 5 action buttons per player. MK2 pinout -1 | N/C 2 | N/C 3 | N/C 4 | N/C 5 | N/C 6 | N/C 7 | Low Punch 1 8 | Low Kick 1 9 | N/C 10 | N/C 11 | Low Punch 2 12 | Low Kick 2 13 | N/C 14 | N/C 15 | N/C MK1 -1 | N/C 2 | N/C 3 | N/C 4 | 2P Low Punch 5 | N/C 6 | Key 7 | 2P Low Kick 8 | N/C 9 | 1P Low Punch 10 | 1P Low Kick 11 | N/C 12 | N/C  

Able to be used with NBA Jam, NBA JAM Tournament Edition, Maximum Hangtime NBA Jam Player 3 or Player 4 Extra Buttons Auxiliary Kick JAMMA+ Harness These are approximately 4 foot long to give you the length needed This kick harness allows you to connect player 3 or player 4 buttons and joystick. You will need 2 harnesses if you want to connect both P3 and P4 to your control panel Pinout -1 GND2 ----3 ----4 ----5 ----6 START7 UP8 DN9 LT10 RT11 SHOOT/BLOCK12 PASS/STEAL13 TURBO14 ----15 ----

WWF Extra Buttons Auxiliary Kick JAMMA+ Harness These are approximately 4 foot long to give you the length needed Each wire has a .187 female quick disconnect on all player controls for attaching to the terminal on the microswitch (Not a cheap connector) This kick harness allows you to connect the bottom buttons for both players. Standard JAMMA connectors only allow for 3 action buttons and Wrestlemania uses 5 action buttons. MK2 pinout -1 | N/C 2 | N/C 3 | N/C 4 | N/C 5 | N/C 6 | N/C 7 | Low Punch 1 8 | Low Kick 1 9 | N/C 10 | N/C 11 | Low Punch 2 12 | Low Kick 2 13 | N/C 14 | N/C 15 | N/C MK1 -1 | N/C 2 | N/C 3 | N/C 4 | 2P Low Punch 5 | N/C 6 | Key 7 | 2P Low Kick 8 | N/C 9 | 1P Low Punch 10 | 1P Low Kick 11 | N/C 12 | N/C  

Check out PDF for all Konami 4 player game kick harness pinouts - Pinout PDF DownloadThese are approximately 3 foot long to give you the length needed Each wire has a .187 female quick disconnect on all player controls for attaching to the terminal on the microswitch AND enough ground connectors for your controls15 pin header connects to your pcbHeader is numbered for you to match what wire goes where on your control panel Wires will vary in color but numbers stay the same!This kick harness allows you to connect player 3 or player 4 buttons and joystickPLEASE NOTE - You will need 2 harnesses if you want to connect both P3 and P4 to your control panel